Electric Fireplace Wall Hanging Ideas

The wall-mount electric fireplaces are ready to use right out of their box. They're a great way to add ambiance without requiring venting or renovation.

They are usually heavy and require careful installation. Follow these steps to set up your new electric fire in the correct way.

1. Connect the Brackets

A wall-mounted or recessed fireplace instantly improves the look of any room. This is an excellent option for those who don't have a fireplace or live in apartments.

Choose the location where you'd like to put your electric fire. It's important to find a location that won't be susceptible to moisture and at a minimum of just a few inches from furniture, drapes and other areas with a lot of traffic. Mark the wall with layout marks to indicate the top and bottom plates of the fireplace frame.

Use a drill or similar tool to drill exploratory holes into the wall. Find studs using an stud-detector. Then, mark the drywall according to the location of the brackets for mounting your fireplace. Next, build out the wall or patch and paint the drywall to prepare it for fireplace installation.

Depending on the wall-mounted fireplace you choose, you may need to install both the firebox and screen in one piece or separate them using a wall bracket. If you aren't sure of your ability to finish this project employ a general contractor or an experienced carpenter.

Most electric wall mounted fire place fireplaces include templates for the installation procedure, but you must also have a spirit level and a pencil in hand to precisely mark the area in which you'll mount the wall brackets. Use the template to ensure that the power cable of the fireplace is able to reach a nearby outlet to plug it in.

Once the studs and the fireplace frame are in place, you can put in drywall that is as smooth and flush as you can for a clean appearance. Add a piece of trim to the bottom edge, and then sand and paint the entire frame to give it a finished look.

You will need to insert the slots or hooks on the back of the majority of electric fireplaces that are wall mounted into the brackets for mounting. Make sure that the slots and hooks are aligned before you connect the fire to the Wall Mounted Electric Fires brackets. Once the fire is set you can then add additional elements such as crystal embers, driftwood log pieces, or decorative rocks.

2. Check the Bottom Bracket

The space above a fire, mantel or chimney breast is a prime spot for hanging artwork. There is a fine balance between an artistic arrangement and one that detracts the overall design of the fireplace.

Generally, the rule of the thumb is that a painting should be around 80% the width of the fireplace or mantel it is placed above. This will keep it proportionate and will make it look nice on the wall. Other decorative and ornamental items placed on the mantel could also influence this size & proportional guidelines.

If you're planning to put a picture above your electric fireplace, you must ensure that the frame is made of glass or another material that is able to withstand high temperatures. If you are unsure, you can test the frame with a temperature sensitive cloth to determine whether it's suitable for this purpose.

One of the most common concerns when the display of artwork over an open flame is the risk of damage to artwork due to smoke or stray heat. While this is not a huge issue with traditional wood or gas-powered fireplace, it's worth examining the manufacturer's recommendations if you're planning to install a wall-mounted electric fire.

The majority of electrical fires come with mounting brackets that can be fixed to the best wall mounted electric fires with hanging screws or wall-mounted fixing systems. If the latter option is used, it's recommended that you drill exploratory holes in a discrete part of the wall prior to you begin mounting your electric fire. After that you can use a pipe & cable finder to check whether there are any pipes or cables in the vicinity of your chosen mounting position.

If there are the electrical sockets, you can decide to place your fire over the electrical socket or move it to a new location. If you decide to move it to a new location you'll need to make sure that the power cable can extend from the fire to the electrical outlet - this is particularly important for older homes or houses with solid walls. If you don't, your electric fireplace will not function properly. Some models come with a template that will show you where to drill the holes to make the holes Some require a spirit-level and pencil to mark the appropriate spots on your wall.

3. Connect the Power Cord

If you've installed a recessed electric fireplace, you might need to move the plug socket from the wall to behind the unit. This can create a sleeker appearance. Be sure to test your fireplace prior to doing this to make sure that everything functions just as it should.

The third option to install an electric fireplace is by framing the space and building it into the wall. This gives a finished traditional look and also allows you to add a mantel. The owner's manual for your model will provide details on framing, wiring and securing the fire.

If you're ready for mounting your new electric fireplace on the wall mounted electric fireplace uk begin by marking the area of installation using a marker or pencil. Then you can use a carpenter's degree to make sure that the area of installation is flat and level. You can also employ a stud locater to mark the location of studs so that you can be certain that you're drilling in a safe area.

Use the electric drill after you have identified the location of installation to make holes for bracket screws or hanging screws. Follow the directions in your owner's guide for this step. This is especially important if you are installing the fireplace into the drywall. If you are unsure what to do then you can ask a professional for help.

You can also hide power cords from view using cable organizer kits. These kits typically come with clips, sleeves or boxes that can be used to bundle cables. You can use wire snakes or fish tape to guide the cables. If you prefer not to cut into your wall or drywall, you can install a power bridge kit for more secure and cleaner connections.

Additionally, you can disguise the wires with paintable covers or by attaching them to the wall or skirting board. Keep the cover or tacks away from sources of heat. This will avoid accidental contact and protect the cord.

4. Connect the adapter

A wall-mounted electric fireplace is an excellent option to make for home improvements or those who don't have the space or funds to put in gas fireplaces. They are easy to install and come ready to use immediately out of the box. They are an excellent choice for those who are seeking a modern and stylish touch or the warmth the fire can bring. These units are designed to be hung like artwork on any wall. They they can be recessed or not at all recessed and are fully electric and have heating powered by fans.

It's a good idea create an inventory of all the tools and equipment you'll require prior to beginning the installation process. You can find detailed instructions on how to mount an electric fire in the user's manual. Some models require that you screw brackets directly into the wall while others could have a mounting plat that slides into slots or hooks on the brackets. It is essential to remove all combustible materials from the area where you will be installing a recessed unit. As a general rule, these materials should be kept 3 feet away from the front of the fireplace and 1.5 feet from its sides.

After you have checked all parts After you have checked all the components, plug in your electric fire and make sure it is working. This is a crucial step, as it will ensure the flame effect screen and heater work exactly as they were intended to. This will also give you an idea of how the product will look in its final position.

Cover the cord when you are confident that it's working correctly. This will keep the final product neat and neat. You can achieve this by installing a new outlet using an outlet cord that can be placed behind the unit. This will give a seamless finish to your fireplace.