Replacement UPVC Door Handles

Find the perfect handle for your door, whether you are replacing a window handle your handles or adding security. upvc door handles handles are simple to fit and comply with the required 92mm centres of multipoint locks.

The most important measurements to take into consideration are the backplate fixing centers and key hole dimensions and levers. Make sure you compare these to your current measurements prior to ordering.

Lever/Pad

Lever pad handles are made up of a lever on one side, and a paddle-shaped handle on the other. These are designed to work with key wind locks although they can also be fitted to multipoint split spindle door locks (though you'll need a separate dual spindle lock case).

Our range of upvc door locks and handles handle lever pads are available in a wide variety of finishes and these will be listed in the drop-down menu once you have found the perfect handle for your door. Not all styles of handle are available in every finish though and you should always check the technical drawings and sizes sections for the particular product you are looking to ensure that you can get the correct size and fitting.

When selecting the new set of lever pad door handles made of upvc door locks and handles it is crucial to make sure that they correspond to the PZ (distance between the spindle of the handle and the center of the hole for the cylinder) of your existing multipoint locks, as they need to be in the same line to allow doors to remain locked, whether from the inside or outside. Our handles are designed to fit most standard cylinders, however it is always worth double glazing door handles-checking before purchasing.

You'll need to take off your existing handles and dismantle the lock case if upgrading to dual spindle handle levers because this will require an additional split inline cylinder. These are available separately, and we provide the complete technical diagram that you can look at in the images for each product.

After you have removed the screws that hold your existing door handle it is recommended to loosen them, and then inspect the mechanism to determine what condition it is in. If the screws are too tight, you may need to loosen them even more. After that, you can take the spindle from the door handle and replace it with a new Upvc handle. It is essential to ensure that the handle is in the right position before fixing it. You can do this by placing your finger between the door frame, and the handle to ensure that it's level.

Lever/Lever

The lever handles on doors are used to operate a multi-point lock with an Euro cylinder. They can be found on many upvc double doors as well as some wooden and aluminum doors. They come in two varieties, with the lever inside and a paddle on the outside. Sprung - these come with a spring cassette within the backplate that helps bring the handle lever into a horizontal position. Non-sprung - these do not include a spring mechanism and will need to be manually pulled to bring the handle lever back to its horizontal position.

To fix the door handle of a lever that is sagging it is necessary to find the hole for access to the detent or pin, which is usually a small rectangle or round shaped hole or protruding pin situated on one side of the handle base plate. Once you have located the hole for accessing the detent or pin, you can take it out using an screwdriver.

Once the handle is placed horizontally, you can install the screws. Make sure to tighten them so that the handle is securely connected to the base plate. Consider applying a threadlocking solution to the threads of screws to increase grip and stop them from loosing over time.

There are a myriad of reasons why lever door handles slide. The most frequent cause is that the fixings are too tight, causing the lever bearing to get tangled against the door. It could also be that the levers have not been adjusted at the right angle, which causes compression of the latch mechanism and stops it from fully springing into operation.

Another reason is that the lever that is sprung is not working properly. This is typically due to the sprung not being in the correct position within the backplate. To check if the handle returns to horizontal, simply move it.

It is important to fix any loose door handles as soon as possible. This could cause excessive wear on the screws, and the handle may even be able to fall off the base plate. It is recommended to tighten all screws that are loose regularly in order to prevent them from becoming loose.

Lever/Snib

These upvc handles are also called "Snib handle sets" and have an snib lock button located at the top of the lever. If you do not have a dummy locking device, you can use this device to secure the door. These handles are fitted with a Fullex lock 68PZ. (68mm between spindle and lock centre). We also have a selection of door handles 68PZ from manufacturers like Ferco and Fab & Fix.

You can make your home more modern by changing your door handles whether you are replacing existing handles or installing new ones on doors that you've constructed. There are a variety of upvc door handle available with traditional levers on backplate, straight or curving short latches and dummy knob handles for multi-point locks, which are ideal for French doors.

Lever on backplate handles are often rectangular in shape but there are also circular or oval shaped versions, which are known as rose door handles. These door handles are characterized by a lever or knob that is attached to the backplate. The backplate is removable for concealed fixing.

There's a wide selection of chrome and colored finishes available for these handles to enhance your door and hardware, including hinges, knobs, bolts and so on. Some handles come with screws that grub the lever or knob firmly to the spindle. Some handles come with bathroom spindles that are suitable for bathroom locks. They also come with a thumbturn release mechanism and can be used on doors for bathrooms.

Mortise

The tubular latch is most likely to be the cause if your uPVC door handle is stuck open. This could be due to various reasons however the most frequent is an absence of lubrication within the latch plate. This can be fixed quite easily by opening the door and spraying lubricant onto the handle and lock. It could also be that the latch plate has become dislodged from the backplate. This is a more complicated issue that requires the assistance of a specialist.

A multipoint handle system is the ideal solution for stuck door handles. These handles are mounted through the faceplate and operated with a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles are available in a number of different sizes to fit various kinds of uPVC doors. They also come with a variety of attractive finishes to match the hardware you already have. These handles can be purchased via the internet or at the local locksmith. They are easy to install and come with clear instructions.

To choose a replacement handle set, you'll need to determine the PZ dimension of the cylinder. This is the distance from the edge of the door frame to the centre point of the hole for the handle in millimetres. You'll also need the type of lock on your door, regardless of whether it's a mortise or hook lock. Once you have these measurements, the simplest way to find the correct handles is to search by brand on the website. This will narrow down the options and you can then choose the right size from there.

A typical handle set includes an arm with two screws of various lengths, drill guides, and installation instructions. The smarter versions, such as the Igloohome Smart Mortise 2+ includes the complete mortice lock, which has an integrated keypad. These are more complicated units and are best suited for professionals who install them or adept DIYers. Some handle sets include a range of additional accessories, such as weather strips, which can be used to enhance the look of the door.