UPVC Replacement Door Handles

As time passes the handles on your doors will wear down and will require replacement. When replacing them, it is crucial that the new handles are in line with the critical dimensions of the handle that was previously used.

The top screw position the lever, and the keyhole dimensions are the three measurements that you need to check. Use the size guide to assistance in this.

Inline Lever/Lever

A lever or lever door handle is a modern handle that can be put in on doors that are new or replacement. This style of handle is available in a variety of styles and finishes. A number of manufacturers offer this handle including Avocet, ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are constructed of durable materials and are perfect for multi point lock doors which require a robust design. The handles are inline and operate off the same spindle and screw fixings, so they can be easily fitted to new or existing uPVC/Composite doors.

The spring lever design allows the handle to be set and angled to ensure a comfortable experience and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles, this will ensure the quality of the finish and performance of the handle over time. The sprung lever can also be reduced to accommodate the widest range of locks. This is particularly beneficial in doors with smaller door frames where the cylinder is further back. A shortened lever can also be used for doors with latches which can be operated with the thumb inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently from lever-type handles found on most doors. These handle types are either operated by one spindle, or two spindles inline or offset. They are commonly utilized on UPVC doors with double glazing. They are available in a range of finishes and variations.

The handles have been tested to the minimum of 200,000 cycles and are available in a variety of finishes, including White, Silver, Chrome & Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with an outstanding performance and durability to serve its intended purpose.

All UPVC lever pads for handles include a spindle and screws, and can be fitted on the upvc chrome door handles door. The backplate fixation centers of 211mm permit a larger handle, which is usually a benefit when replacing a damaged or old multi-point door lock mechanism. These levers for handles are also spring-loaded, which solves the issue of door handles sagging from their horizontal position when they are not in use.

When choosing the replacement UPVC handle and spindle, it is crucial to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement can also be referred to as 'handle centres or cylinder centres'. It is important for matching the correct handles.

Once you have the correct PZ size you will then be required to make sure that the lever pads and push pads are in a suitable shape for the American with Disabilities Act (ADA) compliant handles that you need for your doors. They typically have rectangular or round in shape with an internal lever and an external push pad.

The majority of the UPVC Lever Pads that we offer are spring-loaded. This means that they will return to a horizontal state when not in use instead of hanging and possibly securing to the frame. This helps prevent the draughts and cold air from entering a home. You will also find that the majority of the UPVC lever pad handles are swivel, allowing you to install them on either side of the door.

euro door handles Cylinder

Cylinder locks are typically found on uPVC doors, but can be utilized on other types of door. The cylinder lock is operated with a key that unlocks the cylinder's case. The case is then able to reveal pins that can be aligned with the pins in the lock, allowing them to turn the revolving camera, opening the door. Euro Cylinders can be fitted with up to six pins with internal and external doors usually needing different levels of security.

The selection of a cylinder is vital. It's dependent on the amount of use your doors and handles receive. External doors, for instance are required to be fitted with cylinders that are more secure while doors inside can be secured using the standard cylinder. In addition, some cylinders come with additional features that can improve security even more, like anti-drill or anti-bump features.

To ensure that the euro cylinder is of the right size for your door, it must be measured correctly. The cylinder should be measured from the central fixing screw hole to the end of the cylinder including the thumb turn if you have one. If you are unable to measure using the lock in a fixed position, you can remove it. A cylinder that is protruding beyond the handle and escutcheon could be vulnerable to attacks, such as snapping locks, therefore it is essential that it's not too long.

The design of many modern cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease the chance of attack by forcing cylinders to rotate in a new direction. This will help deflect the attack, and protect your door.

Some cylinders are designed to resist snapping. This is an increasingly common kind of attack on cylinders, where the break line inside the lock is smashed with a special tool to break the front of the cylinder and allow the door to be opened. This is a faster and more convenient method of gaining access than the use of a multipoint locking system. It also leaves less evidence of the break-in which could delay insurance claims.

Spring Cassette

The spring cassette is located in the base of your door handle backplate, providing a spring solution and returning your multipoint lock handles to their rest position after using. Previously a lot of these types of handle did not have a spring built into them, and as a result, they tend to droop or drop once the locking mechanism is disengaged. This component is the best way to address this issue. It also stops your door from getting stuck in the open or closed position as they aren't easy to close manually.

These spring cassettes are specifically designed for use with sprung multipoint locks but they won't work with unsprung multipoint handles and you will need to have a hole specifically cut in the backplate to allow them to fit (please look at the image for a technical diagram). They are a replacement handles for windows for existing damaged or missing cassettes inside the backplates of door handles of many brands of uPVC doors. They are supplied in a single unit. They come with a square cut out that can accommodate an 8mm shaft.

These spring cassettes are a great value for money solution to the issue of your door handles sagging. They are easy to fit and will increase the lifespan of your uPVC doors. For more information on our range of uPVC spares and accessories contact us today. in touch with our team. We are here to assist you and offer expert advice.