How to Replace the Replacement Key Battery For the Saab 9-3

saab 9-3 key fob replacement owners have a unique set of steps to add a second key. It requires dealer service using a handheld computer dubbed Tech-2. Then, a new transponder and key are required to be purchased.

Change your keys regularly to prevent one from deteriorating faster than the other. This will also ensure that your keys remain in good condition.

Replacement Case

As opposed to the traditional saab 9-3 Key keys of the past, the new key fobs contain electronics which makes it hard to make a copy. This has made car theft much more difficult than it was just a few years ago. It has also made it more expensive to replace lost keys.

Every owner of a Saab 9-3 should have at minimum two working keys. It's expensive to replace a lost key because it requires replacing the CIM module, and reconfiguring the locking cylinders. Dealers usually charge between $100-$200 to do this.

There are options to avoid these high costs. Some parts dealers will use the code of an extra key to cut a brand new metal blade at a fraction what the dealer charges. The key must, however, be the same as the original one in order to function in your vehicle.

You can also change the case yourself by following these steps. You'll require a flathead and patience. With the screwdriver, slowly pry the plastic apart and then separate the emergency key from the case. Once the case has been opened take the electronics out and place them into your new case. Be sure to put the correct key and badge back in the case too.

Replacement Battery

The replacement battery for the saab 9-3 key fob replacement 9-3 is a cheap part that can be replaced easily and quickly. This YouTube tutorial for DIY Cyclone Cyd will show you how to replace the remote key fob battery in only four steps. This guide should work with any modern saab-type key fob, however, the procedure may differ slightly.

The button is typically located near the Saab logo on the back of the fob. It's usually next to the Saab logo on the back of the fob. Use a flathead to insert the screwdriver in the small hole in this button. This should be sufficient to let the fob case open in order to change the battery.

After the new battery CR1632 is installed it is possible to reassemble the remote key fob, and then program it to your car. The entire process should take no more than an hour, if not less. This is a simple procedure that doesn't require special tools.

The process is more complicated if you've lost your key, but it is possible. The dealer will need to find the VIN number of the car and then purchase a replacement key blade and TWICE module that has the proper unique code. Then, they'll need to cut the replacement key and then program it with the latest software tool known as MDI.

Replacement Key Fob

The key fob is the device that locks and unlocks your car, it has batteries inside. Batteries are able to last for a short time and eventually will die. This is a typical issue that affects all cars and the good news is that you can replace the batteries in a majority of fobs, without replacing the entire case. You can purchase replacement fobs from Amazon that have all the electronics already installed, so you'll be able to just pop open the case and replace the batteries in the original case. It's important to note that you'll need take out the emergency key first, and you can do this by putting a small flathead screwdriver into the slot found in the middle of the case. The case will split as you rotate the screwdriver around it.

If you're about to replace the keys, make sure you have spare keys, because this can cut down the total cost by a significant amount. If you have a spare you can have the dealer cut the new key and program it into your car, which is cheaper than replacing the whole key fob.

If you don't have a spare one, you can add a second key to your car, however this requires a lot of research and effort. The cost for adding a second key is around a hundred dollars and it also requires programming of the car's computer. This can be accomplished by a professional, however it is an expensive option for most owners.

Replacement Ignition

The modern SAAB 9-3 uses a more sophisticated alarm system built around a key code. If you lose your sole key, it can be expensive to add another one since the car needs to have a special computer added and be programmed to accept a new key. Even a dealer can charge hundreds of dollars to program a new key in the event that they are unable to complete the task.

Dealers will charge you top dollar to replace your car's computer (also called the CIM or saab key replacement cost twice) If you lose your only functioning key. Instead we can reprogram the EEPROM of your current car computer to prepare it for a new key, slashing over 50% of what you'd be charged at a dealership.

If you've owned a 9-3 from SAAB for quite a while you're aware that the ignition keys are not very durable. If your ignition key isn't working properly, you should think about replacing it. They can become very sticky and the buttons can fall off. Fortunately, replacing the ignition key isn't as difficult as it seems, and it can be done fairly quickly using the proper tools.