Replacing uPVC Window Handles

It is simple to change the handles on upvc windows. It is crucial to ensure that the replacement handle fits into the spindle cutout in the window mechanism.

If the steps listed below are followed correctly the cockspur handle will fit most windows. The key is the step size of the handle.

What to Look for

Many of the windows in the UK are fitted with uPVC handles, and over time they will begin to show signs of wear and tear. If this occurs, the handle may become loose or difficult to operate, making it essential to replace window handles it. Anyone who is comfortable working with basic hand tools can complete this relatively simple job.

The first thing to do is make sure the handle is firmly attached to the window frame and is in a position that is open. The next step is to find the pins or screws which hold the handle in place. These are usually located on the inside of the handle. They can be removed with the screwdriver and pliers.

Once the handle has become loose and sagging, gently pull it back from its hinges. Then, you will need to find a new handle in the same style and size. This can be accomplished online or at a local DIY store, and it should take five minutes using the help of a screwdriver.

One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the bottom of the handle to where it rests on the window frame. This is usually an average measurement, but it is important to determine the step height of your existing handle prior to ordering the new one.

There are a variety of sizes based on the kind of handle. Inline handles are offered for uPVC window with centers of 31mm for lugs, while cockspur handles come with centers of lugs of 43mm. Tilt and turn handles are typically found on uPVC windows, and they come with a unique design that allows windows to be tilted in for ventilation, and then rotated to open the window fully.

The most frequent uPVC handle breakage is internal cracking rather than a fracture from the base. This can make it difficult to open. It is essential to ensure that the replacement handle is fitted with the same spindle as the original one.

Remove the old Handle

Incorrectly fitted or damaged window handles could cause double-glazed windows to open and close in a way that isn't correct and may cause them to become stuck. There are a variety of reasons, such as general wear and tear, or corrosion of the handle. In these cases it is crucial to locate replacement handles made of upvc immediately in order to avoid further damage and loss of functionality.

One of the first things that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Begin by removing the screw by the handle while it is in the closed position. This should reveal another screw that once removed, you can then begin to remove the handle itself. You can make the process simpler by using an electric screwdriver.

It is also important to note that the screws on the handle could be hidden behind caps made of plastic, so it is recommended to take the Stanley knife to the screws and take them off. Once the old Upvc door handles handle is removed, take a look at the square cut out on the base of the handle to make sure that the new window lock handles are compatible with it. This is crucial as you will need to measure the length of the spindle on the previous handle to ensure it matches the size of the window mechanism and handle spindle that has been cut out.

There are three types of Upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles that have two screws and Spade handles that are made of flat arms and can be used on either side of the windows made of upvc. Once you have found a suitable replacement, it is just a matter of screwing the handle in place and making sure that the spindle is placed into the lock mechanism. After you have done this you can tighten the handle onto the window frame. Your replacement upvc handles should now be secure.

Measure the Spindle

If you're replacing a upvc window handle that has fallen off, it is likely because the spindle that holds it in place is loose or damaged. In some cases this can be fixed with screws or pins to tighten it. In certain situations it is necessary to replace the handle. There are a variety of handles made from upvc. They include espagnolette bi-fold doors handles inline or cockspur handles. They also have tilt and turn handles. Each type has a different method for installing and replacing the handle.

Before you purchase a new handle, it is essential to know the dimensions of the existing one. This will ensure that the handle will fit the window properly and will be the right size. Fortunately, all handles follow industry standards of sizing making it fairly easy to find the right size.

To determine the size of the handle, turn the window to the open position. Then, you should be able to see the size of the screw or pin that secures it. Make use of a ruler or tape measure to determine the length the spindle is. Once you have the length of your spindle, it is possible to purchase a replacement of the exact same length.

When purchasing a replacement window handle, it is crucial to be aware of the step height of the upvc window handle. The step height is measured from the base to the point at which the handle is positioned on the frame. This is usually about 21mm or 9mm for aluminum and uPVC. Dropping objects into the gap will allow you to determine how far the handle extends before it comes into contact with an obstruction.

Cockspur handles often have different backset heights, based on the style of window handle upvc they are placed in. Inline espag handles have an average height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets depending on the type of window they are placed in. This is because they have spurs that extend from the handle and is secured over the cockspur wedge striker plate.

Install the new handle

When you've chosen a new handle, make sure you align it to the screw holes in the door and secure it with the screws supplied. Install the latch lever the same manner as the handle that you are replacing if you are also replacing the door handle. Then, attach the door trim again to conceal the screws for mounting.

Tips: To remove a metal head from a wedge made of wood, place the handle on the floor so that its wide end is on the floor. Then use a hammer and tap the narrow end. Be careful not to damage the handle or the spindle.