UPVC Replacement Door Handles

Over time, the handles on your doors will wear out and need to be changed. In this case, it is essential that the new handles are in line with the critical dimensions of the previous handle.

The top screw position, the lever and the keyhole dimensions are the three measurements you need to check. Refer to the size guide for help with this.

Inline Lever/Lever

A lever/lever handle is a contemporary door handle designed to work with new or replacement doors. This type of handle is available in many styles and finishes. A number of manufacturers make this handle including Avocet, ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles of uPVC/Composite are made of sturdy materials and are suitable for doors with multi-point locks that require a strong design. The handles are inline and they use the same screws and spindle to fix them. They can be easily mounted on new or existing uPVC/Composite door.

The spring lever design allows the handle to be placed and angled to ensure a comfortable experience and is suitable for all users. The handle has been tested to 200,000 cycles, which will ensure the quality of the finish and the performance of the handle over time. The lever that is sprung can be cut to fit more locks. This is particularly beneficial for doors with narrower frames, where the cylinder is further back. A lever that is shorter is an ideal choice for doors where the latch can be operated by a thumb turn located on the inside.

Lever Pad

A Lever Pad upvc door handle operates differently than lever handles on doors. These handle types can either operate from a single spindle (inline) or independently from each side using two offset or inline spindles (pad). They are typically employed on UPVC doors with double glazing. They come in a variety of finishes & variations.

The handles have been tested to the minimum of 200k cycles and are available in several finishes, including White and Silver, as well as Chrome & Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high level of durability and performance for the intended use.

All of the UPVC lever pad designs are supplied with a spindle and screws, allowing them to be installed on any new or existing uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is usually an advantage when replacing a damaged or old upvc door handles multi-point door lock mechanism. These handle levers are also sprung, solving the problem of handles that slide out of their horizontal position when they are not being used.

When choosing the replacement UPVC handle and spindle, it is crucial to match the PZ dimensions of the multipoint sash lock door handles as well as the uPVC door. This measurement is often referred to as the "window handle repairs centre" or "cylinder centres' and is a critical aspect of matching up the appropriate handles.

After you have determined the correct PZ size, you will need to make sure that the lever and push pads are designed to match the American with Disabilities Act compliant handles you require for your door. They are typically round or square with an internal lever and an external push pad.

The majority of the UPVC Lever Pads we sell are sprung. This means they can be reverted to a horizontal state when they are not in use instead of hanging and possibly securing to the frame. This stops draughts from entering the home. Also, the majority of UPVC lever pad handles are handed which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and other kinds of doors. Cylinder locks are operated by using a key that unlocks the cylinder's case. This exposes pins that can be aligned with those inside the lock and allow them to rotate the camera that rotates, opening the patio door handle. euro lock handles cylinders can be equipped with up to six pins with internal and external doors usually having different levels of security.

The choice of the correct cylinder is crucial; it depends on the way your doors and handle are utilized. Doors that are external, for instance should be equipped with higher security cylinders and doors inside can be secured using an ordinary cylinder. Additionally, certain cylinders have extra features that can improve security, for instance anti-drill or anti-bump features.

To ensure that the euro cylinder is the correct size for your door, it should be measured correctly. The cylinder must be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn if there is one. It is best to do this with the lock in place however in the event that this is not possible, you can remove it to measure. A cylinder that is protruding beyond the handle and escutcheon could be susceptible to attacks like snapping locks, therefore it is essential that it is not too long.

The design of many modern cylinders has anti-drilling and bump resistance features. These features are designed to minimize the chances of an attack by forcing the cylinder rotate in an opposite direction. This can to deflect an attack and ensure your door is secure.

There are cylinders that have been made to resist snapping. This is a typical attack on cylinders. A specially designed tool is used to break the lock's break line and then the front of the cylinder is snapped off. This is a quicker and easier way to gain access than using the use of a multipoint locking system. It also leaves no evidence of the break-in which could make it difficult to prove insurance claims.

Spring Cassette

The spring cassette is located inside the base of your door handle's backplate providing a sprung solution and returning the multipoint lock handles back to their rest position after using. There was a time when handles of this kind didn't have a spring built into them, and as a result, they tend to droop or drop when the locking mechanism is disengaged. This simple component is the best way to address this issue. It also prevents your upvc door from becoming stuck in either the open or closed position since they are difficult to close manually.

These spring cassettes have been specifically made for use with multipoint locks that are sprung They will not work with non-sprung multipoint handles. You will require a bespoke hole cut into your backplate in order for them to fit (please look at the image for a technical diagram). These cassettes are a solution to damaged or missing cassettes on the backplate of uPVC door handles. They feature an elongated square that allows for an 8mm spindle to be used and are sold as a set.

These spring cassettes are a fantastic value for money way to fix the problem of door handles that are sagging. They are simple to install and will extend the life of your uPVC door. Please contact our team to learn more about our selection of uPVC accessories and spares. We are available to assist you and provide professional advice.