How to Change a Subaru Spare Key

Call a locksmith if you are missing your subaru forester key replacement key. Usually, they will cut keys for you much less expensively than the dealer.

Subaru car keys are typically either smart "push-to-start" fob remote keys or basic keys made of metal. The Fob key has a chip in it and must be reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes function with the keypad in your car to connect with your computer system of your vehicle.

Subaru models offer a little known feature called PIN Code Access. You can use a customized number sequence to open and start your car. If you own a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that came with this feature, check the owner's manual to learn how much is a new subaru key fob to use it.

If your locked keys in subaru forester stop working, there's a good possibility that the battery inside the key fob is dying. You can check the battery life of your key fob using a portable tester or a multimeter you can find in your garage.

The next step is to remove the key fob from its case, and then examine the circuit board of its transmitter. It will have one or two sets of eight-digit numbers, so make a note of the first set so that you can recall it later. Once you've completed this, you can begin programming your key fob at home. This procedure is different based on the model and year your car. However, it is generally easy enough to do yourself.

Key Fobs

Subaru's newest models feature key fobs that can not only unlock doors but also turn on lights, lock gas cap and even start the car. This last trick is particularly beneficial if your experience includes arriving at the gas station only to discover that your car isn't starting because the battery for the key fob has died.

It doesn't matter if your Subaru is new or older you can be sure that the key fob can be replaced without difficulty. It's important to remember that the most recent models that have the highest level of technological sophistication could require an excursion to the dealer. However, with just a little time and effort, you'll have your replacement key fob ready to go at home.

Begin by looking at the circuit board for the transmitter inside your key fob (instructions to open the case should be provided in your owner's manual). There should be one or two serial numbers with 8 digits each. Keep the first set of numbers on hand for future reference.

Next, climb into your driver's seat and shut all the doors. Turn the key 10 times to start your car, then turn off the engine. Press the lock button on your key fob, then open the door. This will test that your doors are working properly. Close the door, and then take the key off. The car should sound again, signalling that the key fob has been programmed.

Ignition System

The battery for the key could be dead if your Subaru xv replacement key keys don't work as they should. If you are aware of the issue, you can change the battery on your key fob yourself. A replacement battery is cheap and is fairly easy to locate. If the key fob doesn't respond to your commands there could be a different issue. To find a spare key, it's recommended to visit a dealer. They will ensure that the key is an original Subaru key, that is in warranty, and will be programmed for your vehicle. This is much simpler and safer than getting an aftermarket key from a website.

You can also request that the dealer cut a new key if you supply them with your VIN number as well as evidence of ownership. They'll utilize this information to encode the new key in order to be accepted by your immobilizer. This is more complex than cutting a key, and the dealer will typically charge more for this service.

After the new key has been programmed it will be able to change it over to your existing key. It takes just five seconds to insert the new key, so keep your working key close to your side. You can remove the key after the security light stopped flashing and test it.

Battery Replacement

One of the key advantages that make Subaru fobs useful is their ability to switch on your car's power windows and sunroof with just a press of the button. But, the battery in the replace subaru key key fob isn't designed to last forever and will eventually need to be replaced. Fortunately, replacing the battery is a simple process that you can complete yourself with the help of this short guide from Capitol subaru legacy key replacement.

To start you'll need to find the small crevice in the seam that separates the back and front of your key fob. It is possible to open this seam with the flat-head screwdriver, which will reveal the small compartment that contains the battery. Install the new battery and ensure it is facing the right way. Remove the old one. Once everything is reassembled, you can use your new key fob to lock, unlock, and start your vehicle easily!

It's always recommended to have an extra set of keys on hand especially if you've lost them or they're not functioning properly. You can buy a new key from your local dealership or have it cut by locksmiths. In either case, it's vital to get your key fob functioning properly as soon as you can to ensure you drive safely!